基于Abaqus的双裂纹不同间距对裂纹扩展速率的研究

扩展有限元法是近年经过大量运用的,在传统有限元的范围中求解不连续问题一种有效计算方法,它是基于单位分解的思想,在计算不连续问题时加入跳跃函数。以ABAQUS为平台,基于扩展有限元方法 (XFEM),以含双穿透型裂纹的有限宽板受横向拉伸载荷为力学模型,建立相应的裂纹尖端应力的有限元模型,研究焊接接头区域不同间距双裂纹相互作用对裂纹扩展速率的影响。结果表明:双裂纹间距的的大小并没有对裂纹的扩展速率产生影响。     

负径向电场对带电粒子俘获率影响的数值模拟

本文采用数值方法求解Grad-Shafranov方程反演EAST典型长脉冲放电实验(炮号33068)的平衡位形和磁场分布，进而结合粒子在托卡马克电磁场中的运动方程，模拟氘离子在负径向电场存在时的运动轨迹，并统计不同负径向电场下的氘离子俘获率。结果表明：随负径向电场的增大，氘离子轨迹由扩张通行轨迹向外翻香蕉轨迹再向内翻香蕉轨迹，最后向压缩通行轨迹演变；氘离子俘获率随负径向电场的增大而减小，氘离子初始速度越小，其变化越大。     

瞬态闭锁试验在0.13 μm大规模集成电路中引起的潜在损伤

瞬态剂量率辐射试验会引起集成电路发生损伤或失效，其原因至少有两种：闭锁大电流引起的电路内部金属互连熔融；累积电离总剂量引起的氧化层电荷造成阈值电压偏移。本文以一种0.13 μm体硅CMOS处理器为对象，研究了瞬态剂量率和稳态电离总剂量辐射效应规律。结果表明：瞬态剂量率闭锁效应对处理器造成了显著的潜在损伤，导致其总剂量失效阈值从1 030 Gy(Si)降低至600 Gy(Si)。研究结论对于大规模集成电路的可靠性评估和指导辐射加固设计有重要参考意义。     

硫酸体系中锰钽铌矿加压浸出研究

针对单一硫酸体系锰钽铌矿加压浸出下钽铌浸出率均不到10%的问题,在硫酸体系引入助浸剂,考察氟化铵、双氧水、反应压强、硫酸浓度、反应温度、氟化铵矿比对锰钽铌矿加压浸出的影响,采用XRD对浸渣进行物相表征。实验结果表明,在锰钽铌矿加压浸出中,引入助浸剂氟化铵,温度200℃、硫酸浓度50%及氟化铵/矿比为0.8∶1的条件下钽浸出率超过93%,铌浸出率超过96%。引入氟化铵对硫酸体系下锰钽铌矿的加压浸出效果的提升十分显著。     

FeNi@SiO2磁性纳米复合粒子的制备及磁热性能

大量制备磁热性能优异的磁性纳米粒子对磁热疗和组织复温的生物学应用具有理论价值.本研究通过高温电弧法制备FeNi磁性纳米颗粒,通过超声-沉降分级筛分得到平均粒径为80 nm的FeNi纳米颗粒,通过溶胶-凝胶法得到平均粒径为100 nm,SiO2壳层厚度为15～20 nm的FeNi@SiO2纳米复合粒子.超导量子干涉仪测定FeNi@SiO2纳米复合粒子饱和磁化强度Ms为80 emu/g.模拟磁热疗条件下,FeNi@SiO2磁性纳米粒升温速率为3.6℃/min,满足磁热疗应用要求.模拟组织复温条件下,FeNi@SiO2磁性纳米粒升温速率为61.8℃/min.磁性复合纳米粒子在不同溶剂、不同温区条件都显示了良好的热性能,可作为温度激活剂应用于磁热疗及冷冻组织的复温.本研究对磁性纳米材料的生物学应用研究具有一定的参考价值.     

Non-linear dissolution mechanisms of sodium calcium phosphate glasses as a function of pH in various aqueous media

Phosphate glasses for bioresorbable implants display dissolution rates that vary significantly with composition, however currently their mechanisms of dissolution are not well understood. Based on this systematic study we present new insights into these mechanisms. Two-stage dissolution was observed, with time dependence initially parabolic and later linear, and a two-stage model was developed to describe this behaviour. Dissolution was accelerated by lower Ca concentration in the glass, and lower pH in the dissolution medium. A new dissolution mechanism is proposed, involving an initial stage where diffusion-controlled formation of a conversion layer occurs. Once the conversion layer is stabilised, layer dissolution reactions become rate-limiting. Under this mechanism the transition time is sensitive to the nature of the conversion layer and solution conditions. These results reveal the dependence of P₂O₅–CaO–Na₂O glass dissolution on solution pH, and provide new insight into the dissolution mechanisms, particularly regarding the transition between the two dissolution stages.     

Effects of upholstery materials on the burning behavior of real‐scale residential upholstered furniture mock‐ups

Fire spread and growth on real‐scale four cushion mock‐ups of residential upholstered furniture (RUF) were investigated with the goal of identifying whether changes in five classes of materials (barrier, flexible polyurethane foam, polyester fiber wrap, upholstery fabric, and sewing thread), referred to as factors, resulted in statistically significant changes in burning behavior. A fractional factorial experimental design plus practical considerations yielded a test matrix with 20 material combinations. Experiments were repeated a minimum of two times. Measurements included fire spread rates derived from video recordings and heat release rates (HRRs). A total of 13 experimental parameters (3 based on the videos and 10 on the HRR results), referred to as responses, characterized the measurements. Statistical analyses based on Main Effects Plots (main effects) and Block Plots (main effects and factor interactions) were used. The results showed that three of the factors resulted in statistically significant effects on varying numbers of the 13 responses. The Barrier and Fabric factors had the strongest main effects with roughly comparable magnitudes. Foam was statistically significant for fewer of the responses and its overall strength was weaker than for Barrier and Fabric. No statistically significant main effects were identified for Wrap or Thread. Multiple two‐term interactions between factors were identified as being statistically significant. The Barrier*Fabric interaction resulted in the highest number of and strongest statistically significant effects. The existence of two‐term interactions means that it will be necessary to consider their effects in approaches designed to predict the burning behavior of RUF.     

A benzoate coprecipitation route for synthesizing nanocrystalline GDC powder with lowered sintering temperature

Electrolyte powders with low sintering temperature and high-ionic conductivity can considerably facilitate the fabrication and performance of solid oxide fuel cells (SOFCs). Gadolinia-doped ceria (GDC) is a promising electrolyte for developing intermediate- and low-temperature (IT and LT) SOFCs. However, the conventional sintering temperature for GDC is usually above 1200 °C unless additives are used. In this work, a nanocrystalline powder of GDC, (10 mol% Gd dopant, Gd_0.1Ce_0.9O_1.95) with low-sintering temperature has been synthesized using ammonium benzoate as a novel, environmentally friendly and cost-effective precursor/precipitant. The synthesized benzoate powders (termed washed- and non-washed samples) were calcined at a relatively low temperature of 500 °C for 6 h. Physicochemical characteristics were determined using thermal analysis (TG/DTA), Raman spectroscopy, FT-IR, SEM/EDX, XRD, nitrogen absorptiometry, and dilatometry. Dilatometry showed that the newly synthesized GDC samples (washed and non-washed routes) start to shrink at temperatures of 500 and 600 °C (respectively), reaching their maximum sintering rate at 650 and 750 °C. Sintering of pelletized electrolyte substrates at the sintering onset temperature for commercial GDC powder (950 °C) for 6 h, showed densification of washed- and non-washed samples, obtaining 97.48 and 98.43% respectively, relative to theoretical density. The electrochemical impedance spectroscopy (EIS) analysis for the electrolyte pellets sintered at 950 °C showed a total electrical conductivity of 3.83 × 10^?2 and 5.90 × 10^?2 S cm^?1 (under air atmosphere at 750 °C) for washed- and non-washed samples, respectively. This is the first report of a GDC synthesis, where a considerable improvement in sinterability and electrical conductivity of the product GDC is observed at 950 °C without additives addition.     

Deep-blue thermally activated delayed fluorescence emitter with a very high fluorescence rate

Conventional thermally activated delayed fluorescence (TADF) molecules achieve small energy differences between the lowest singlet and triplet excited states (ΔE_ST) by enhancing the intramolecular charge transfer, which inevitably leads to a wide emission spectrum and low fluorescence rate. Here, we prepared a deep blue TADF molecule via a small ΔE_ST pyridine-phenol fluoroboron complex as the acceptor. The small ΔE_ST is maintained when carbazole donors are attached to the 4-position of the phenyl rings in the fluoroboron complex. Benefiting from the strong electron coupling between the donor (D) and acceptor (A) moieties, the compound Cz-4-BF exhibits a high fluorescence rate of 4.8 × 10⁸ s⁻¹ and a small D-A dihedral angle change in the excited state. Consequently, a photoluminescence (PL) quantum yield of nearly 100% and a PL spectrum with full-width at half-maximum (FWHM) < 60 nm were obtained in solution and low-concentration doped films. A TADF-sensitized fluorescence (TSF) device containing Cz-4-BF achieves an external quantum efficiency of 21%, which is higher than the devices employing classical fluorescent emitters and multiple resonance-type TADF emitters. The Cz-4-BF-based TSF device shows significantly improved color coordinates of (0.14, 0.10) versus a control device without Cz-4-BF.     

腔磁力系统中的诱导透明和快慢光传播

为了在腔磁力系统中实现可控的磁子诱导透明、磁力诱导透明以及快慢光传播,建立了一个混合腔磁力系统.该系统由一个含有YIG球的微波腔和在z方向对球施加一个均匀的偏置磁场组成,并用强泵浦场驱动磁子和弱探测场驱动微波腔.研究表明,通过调节腔与磁子之间的相互作用强度和微波腔与磁子的耗散比,可以增加磁子诱导透明(MIT)、磁力诱导透明(MMIT)的效果和提高快慢光传播的速度.该研究结果可为磁力诱导放大、量子光学操纵和量子信息存储以及灵敏光开关的研究提供参考.